Guangmai Technology is professional in making the LED COB infrared 850nm 50W 100W Chip.
Salah faham dalam penggunaan LED inframerah dalam kamera pengawasan keselamatan
1. The importance of heat dissipation is relatively neglected: we often use too small heat sink or no heat sink at all. It is important to know: Poor heat dissipation will result in high operating temperature of the chip, resulting in infrared wavelength drift and reduced photoelectric conversion efficiency. The high wavelength, exceeding 850nm, causes the camera's CCD to have poor light sensitivity, that is, the night vision effect becomes worse. Low photoelectric conversion efficiency means insufficient brightness. Often a few cents of heat sink will produce the big effect of the small soldiers making great contributions.
2. Wrong hand touch to test the temperature: people often get shocked by themselves, because they can't bear it in less than 2-3 seconds when they put their hands on the shell (or heat sink) over 44 degrees Celsius, so I feel "Too hot", in fact, the temperature is not high and will not harm the normal operation of electronic components at all. Moreover, the higher the temperature of the housing (or the heat sink), the better the heat dissipation. "Energy is indestructible"---Imagine: The shell (or heat sink) is not hot. Where does this "heat" go? The heat stays on the chip and cannot be led out, which causes the chip to work under high temperature, and the night vision effect is poor, the light decay is large, and the lifespan is short.
3. Think that a larger chip must be "brighter" than a smaller chip: Therefore, LEDs that require large-size chips are often blindly designated. You know: the brightness depends on the current, how much current can be used? It depends on the processing of heat dissipation, that is: heat dissipation determines the current and thus the brightness, not the size of the chip determines the brightness. In theory, regardless of the size of the same brand of chips, if the current and voltage are the same (same power), the heat generated will be the same. The question is: How much area is the same heat spread? Scattered on the pinhole-sized area and the palm-sized area, the difficulty of heat dissipation is greatly different. In terms of heat dissipation, each company has different technologies, equipment, and heat dissipation materials. Therefore, each company has a different ability to deal with the same "heat" in how much area.
For example: if you provide 1.2A current on Epistar 28mil chip and 42mil chip, the voltage is slightly the same (about 1.7V), so the power is slightly the same (about 2W), and of course the heat generated is similar. The problem is: It is easier to dissipate the 2W heat on the area of the 42mil chip, but it is more difficult to disperse it on the 28mil chip. Using traditional silver glue to "bond die" packaging method, its thermal resistance is generally 20 degree -30 degree /W, and using eutectic technology packaging, its thermal resistance is generally 6 degree -10 degree /W. It shows that the heat dissipation effect is completely different. The driving currents that can be used by the above two are greatly different, and the brightness is also very different.
Sudah tentu, penggunaan teknologi pelesapan haba termaju untuk memilih pembungkusan cip kecil dan kaedah pemanduan arus tinggi juga terhad. Jika haba 2W di atas diletakkan pada kawasan cip 10mil, walaupun ia dibungkus dengan proses eutektik, pada masa ini sukar untuk memanaskan Eksport dengan lancar dan sepenuhnya. Melihat masa depan, dengan teknologi dan bahan pelesapan haba yang lebih baik, mungkin untuk mencapai LED inframerah yang lebih maju dengan cip yang lebih kecil dan harga yang lebih rendah, tetapi dengan kesan penglihatan malam yang sama.
To sum up: the night vision effect of a large-size chip may not be stronger than that of a small-size chip, depending on the quality of the heat dissipation process. Therefore, the packaging technology of the eutectic process is one of the important means for the improvement of cost performance at present, and it should be the future trend.
LED COB inframerah 850nm 50W 100W Cip package size:
LED COB infrared 850nm 50W 100W Chip application:
Mengenai LED Guangmai/ LED GMKJ
Lembaran data:
Untuk butiran lanjut, sila hubungi terus Guangmai Tech.
Anda boleh memuat turunLembaran data Versi Bahasa Inggeris of LED COB infrared 850nm 50W 100W Chip from the head of this page.
Cool tags: led cob inframerah 850nm 50w 100w cip, China, pengilang, pembekal, kilang, harga, murah, sebut harga, lembaran data, spesifikasi, spesifikasi
